Scan the picklist number. A picklist can be scanned if the following verifies:
After the user scanned the pick list, the system identifies the wave.
If the ‘Use for multi picking’ option is not set for the pick list type of the pick list, it cannot be picked in the multi picking flow. When picking a wave that contains such pick lists, the user has to scan these pick list among the other pick lists, but these pick list will not be taken into account when the system list the items to pick.
If the ’Multi picking: Allow to select wave?’ option is enabled on the Pick List Controller, the wave can be selected from a list.
Identify the moveable location. Only moveable locations from the same warehouse as the pick list can be scanned. The scanned moveable location will be assigned to the pick list. One moveable location can only have one pick list assigned.
If the ‘Multi picking: Set movable location at start of picking? (Y/N)’ option is set to true on the pick list controller, the system identifies the wave after the first pick list is scanned and automatically proceeds to the Select item to pick screen.
The moveable location will be assigned to the pick list after the first item from the pick list is picked.
Scan the next pick list number. A pick list can be scanned if it is in the same wave as the first scanned pick list.
Scan the next pick list number or press the Done button to start picking the scanned pick lists.
A pick list can be scanned if it is linked to the same warehouse as the first scanned pick list.
If Pick and Pack remarks were added to the pick lists, the remarks will be shown after pressing the Done button or scanning every pick list. Press the Ok button to acknowledge the remark.
After pressing the Done button, or after scanning every pick list in the wave, the list of the items to pick is displayed. Every item from the scanned pick lists that is not yet picked is listed.
If the ’Allow to select the item to pick?’ setting is not enabled on the pick list controller, the system will automatically start the picking with the first item on the list.
On the bottom of the screen the picking data is displayed:
Scan the pick location or select it from a list after pressing the Select location button.
To perform other tasks, press the Other tasks button.
When the ‘Skip screen to identify the pick location? (Y/N)’ option is set to true on the pick list controller, the system will automatically proceed with the allocated pick location and goes to the Scan a product screen. Please see: 7. Identify product
Press the Other tasks button to perform the following actions:
Scan the product or select a product from a list after pressing the Select a product button. Every item on the pick location is listed.
When the ‘Disable selection of items’ option is set to true on the pick list controller, the item cannot be selected.
When there are more than one batch of the item on the pick location, it has to be verified that the right batch is picked. When the product has been identified by scanning, the system will check that whether the batch and best before date information are included in the barcode. If it is, the system will automatically proceed with that batch and best before date and skips this screen.
Select the batch from the list. The following information is displayed on the screen:
Only the allocated batch can be selected.
If the ‘Auto select batch/BBD on picking?‘ option is set to true on the pick list controller, the system will automatically select the batch and will skip the screen automatically.
After the product to pick has been identified, add the quantity to pick. For more information about the quantity adding screens see: Screens for entering additional information.
The number of the picked items can be modified, however there is a maximum limit:
Identify the movable location to pick onto. Only the movable location assigned to the picklist can be scanned or selected.
On the bottom of the screen the following information is displayed:
In case there is an SSCC assigned in the Prepare carts flow, at this point you can scan the destination SSCC so that you can make sure that the items are in the right box.
On the screen you can see the SSCC number to be scanned and the movable location is also displayed.
With this step the status of the items becomes packed. You can start a Consolidated packing flow to double check the content of the boxes or the stock can go a through a shipping process immediately.
It is possible, through custom development, that multiple boxes are prepared for one pick list. If there are multiple boxes and it is not exactly defined what needs to be stored in which box, you will see a list of SSCC’s on the screen and you need to scan one of them.
After every item was picked, the system goes back to the ‘Scan the pick list number’ screen.
Because in the multi-picking flow it is mandatory to pick onto a moveable location, the status of the pick list after the picking will always be ‘Picked’ and the stock has to go through packing before it can be shipped.