implementation:wms:install_notificationlistener
Differences
This shows you the differences between two versions of the page.
| Both sides previous revision Previous revision Next revision | Previous revision | ||
|
implementation:wms:install_notificationlistener [2018/01/19 15:13] csuhaa |
implementation:wms:install_notificationlistener [2020/01/17 14:31] (current) vise |
||
|---|---|---|---|
| Line 1: | Line 1: | ||
| - | ==== 3.2.3. Produmex SB1 Notification listener ==== | + | ==== 3.3.3. Configure the Produmex SB1 Notification Listener ==== |
| - | === 3.2.3.1. Configuring the database === | + | Note: Make sure you do not perform the configuration on an environment with active users. |
| - | In order to activate the SB1 Notification listener, you need to enable the service broker; first you click the config button of the Produmex SB1 Notification Listener. This will show the following screen: | + | In order to activate the SB1 Notification listener, you need to enable the Service Broker as follows. |
| - | {{:implementation:Installer_SB1Notif.png?nolink|}} | + | 1. On the Produmex Suite Installer screen click the ''Config'' button of the Produmex SB1 Notification Listener. |
| - | Click the “Run in console Mode” button of the configuration database option. This will show the following console. | + | 2. Click the ''Run in console mode'' button of the Configuration Database option. |
| - | <wrap round important>Do **NOT** perform this action on an environment with active users.</wrap> | + | {{ :implementation:wms:installation:configure_database.png |Configuring Produmex SB1 Notification Listener}} |
| - | {{:implementation:Installer_SB1Notif_2.png?nolink|}} | + | It shows the following console. |
| - | Simply hit ENTER to finish the database configuration. | + | {{:implementation:Installer_SB1Notif_2.png?nolink|Produmex SB1 Notification Listener}} |
| + | 3. Press ''ENTER'' to finish the database configuration. | ||
| - | === 3.2.3.2. Listing the actions === | + | Now list the actions that the Produmex SB1 Notification Listener needs to listen to by proceeding as follows.\\ |
| - | You need to list any actions where that the Produmex SB1 Notificationlistener needs to listen to.\\ | + | 4. Click the ''Run in console mode'' of the List Actions option. |
| - | To do this click the “Run in console mode” of the list actions option. | + | |
| - | {{:implementation:Installer_SB1Notif.png?nolink|}} | + | {{ :implementation:wms:installation:list_actions.png |Configuring Produmex SB1 Notification Listener}} |
| - | The tool will add the actions to the config-file located in the installation folder of the Produmex SB1 Notificationlistener. | + | The tool adds the actions to the config-file located in the installation folder of the Produmex SB1 Notification Listener. |
| - | {{:implementation:Installer_SB1Notif_4.png?nolink|}} | + | {{:implementation:Installer_SB1Notif_4.png?nolink|Produmex SB1 Notification Listener}} |
| - | Afterwards press ENTER to exit. | + | 5. Press ''ENTER'' to exit and close the screen of the options. |
| + | |||
| + | 6. Click ''Save'' on the Produmex Suite Installer screen and close it. | ||
| + | |||
| + | Continue with section [[implementation:wms:install_storedprocedures|3.4. Adaptation of stored procedures.]] | ||
implementation/wms/install_notificationlistener.1516374798.txt.gz · Last modified: 2018/01/19 15:13 by csuhaa
